HappyModel CrazyBee F4 Pro V2.2 FC
CrazybeeX series flight controller is the first 5in1 AIO flight controller which could handle 2s.
It’s a better upgrade flight controller for your whoops. We could use this flight controller to building a 1s-2s compatible lightest 65mm/75mm/85mm brushless whoop or 2-3inch ultra light toothpick
| Flight controller | MCU:STM32F411CEU6 (100MHZ, 512K FLASH) Sensor: MPU-6000(SPI connection) Board size: 28.5 * 28.5MM Power supply: 1S-2S battery input (DC 2.9V-8.7V) Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready Built-in Betaflight OSD(SPI Control) Built-in 5.8G VTX Built-in SPI Frsky receiver support D8/D16 Built-in 5V 1A BEC Built-in voltage detection Firmware target: CrazybeeX FR version: Recommend Betaflight 3.5.7 target CRAZYBBEF4FR CrazybeeX FS version: Recommend Betaflight 3.5.7 target CRAZYBBEF4FS CrazybeeX PNP version: Recommend Betaflight 3.5.7 target CRAZYBEEF4DX |
| Onboard 4in1 ESC | EFM8BB21 Power supply: 1-2S LiPo/LiPo HV Current: 5A continuous peak 6A (3 seconds) Support BLHeliSuite programmable Factory firmware: S_H_50_REV16_7.HEX Default protocol: DSHOT600 |
|
(CrazybeeX FR V2.2 version) Onboard Frsky SPI receiver |
SPI BUS receiver Frsky D8/D16 compatible Support Frsky_X_LBT(EU-LBT), Futaba S-FHSS (Need Betaflight 4.0.5 firmware or latest) Channels: 8ch/16ch Failsafe support No ground interference ( Transmitter and receiver 1 m from the ground): 100m~200m |
|
(CrazybeeX FS V2.2 version) Onboard Flysky SPI receiver |
SPI BUS receiver Protocol: AFHDS and AFHDS-2A Switchable Channels: 8ch(AFHDS) or 14ch(AFHDS-2A) No ground interference ( Transmitter and receiver 1 m from the ground): 100~200m Failsafe support |
| (CrazybeeX PNP V2.2 version W/O on board receiver) | No onboard SPI receiver |
| Onboard 5.8g VTX | Output power: 25mw~200mw switchable Frequency: 40CH Input voltage: 3.3V 5.5V Current consumption: 300mA(type) Frequency: 5.8GHz 5bands 40 channels With Race band Smartaudio ready Default vtx_power is 3 Should set vtx_low_power_disarm = ON to reduce the high temperature when test on the ground |
| Onboard Voltage and Current detector | Voltage Meter scale “110” Amperage Mete scale “1175” |
CrazybeeX FR V2.2 Bind procedure:
- Make the on board receiver get into bind mode: Plug USB and then press the bind button for 1 second , the Red LED on the top of the flight controller will getting to be solid , this indicate the receiver is in bind mode; Or use bind code to bind :For 3.5.7 version firmware Plug USB and then connect Betaflight configurator and then move to CLI tab , type “Frsky_bind”, the Red LED on the top of the flight controller will getting to be solid , the onboard receiver is in bind mode; For 4.0.x the bind code is “bind_rx_spi” ,For 4.1.x or 4.2.x the bind code is “bind_rx”
- Make your Frsky transmitter get into bind mode . If bind is successful the red led will starting to blink. The red LED wouldn’t blinking when binding with some new ACCESS firmware frsky radio , but the bind is actually successful , need to go to CLI command and type “save” to finish the binding .
CrazybeeX FS V2.2 Bind procedure:
- Make the on board receiver get into bind mode: For 3.5.7 version firmware Press and hold the bind button for 1 second ,then plug USB, the Red LED at the bottom of the flight controller will blinking fast , this indicate the receiver is in bind mode; For 4.0.x version firmware Plug USB and then connect betaflight configurator and then move to CLI tab , type “bind_rx_spi” ,the Red LED at the bottom of the flight controller will blinking fast , the onboard receiver is in bind mode; For 4.1.x or 4.2.x the bind code is “bind_rx”
- Make your Flysky transmitter get into bind mode . If bind is successful the red led will getting to be solid.
SPI Receiver option:
Frsky_D compatible with Frsky D8 protocol
Frsky_X compatible with Frsky non-eu D16 protocol
Frsky_X_LBT compatible with Frsky EU-LBT D16 protocol (4.0.X or latest betaflight firmware support)
SFHSS compatible with Futaba S-FHSS protocol
A7105_FLYSKY_2A compatible with Flysky AFHDS-2A protocol
A7105_FLYSKY compatible with Flysky AFHDS protocol
Shipping & returns Carriers: Full Send FPV uses the United States Postal Service for most shipments, however, we may use other carriers to deliver your order (typically for lipo battery shipments).
UPS Shipping: Note, that UPS does not deliver on Saturdays. We recommend using USPS for all shipments, but UPS is an available option.
Lost Packages: Full Send FPV is not responsible for lost packages. No refunds will be provided if your package is lost in the mail system. It is our recommendation to select the Priority Mail option with the United States Postal Service to ensure that packages are not lost, and that you have at least $50 in insurance. Priority Mail has the most reliable package tracking to ensure packages arrive at their specified destination.
Shipping Time & Delays: Unless otherwise indicated, orders received prior to 4 pm with payment received will usually ship that day, unless it is a holiday or non-business day.
Delivery timeframes provided are estimates and will depend on the carrier. Full Send FPV will not be held responsible for any delays caused by a mail carrier or local postal service.
CLICK HERE for the full Shipping.& Returns Policy